Most searches for a ci flexo printing machine china come from a bag maker who already knows what flexo is. The question behind the search is narrower: which width, which repeat, and can the machine finish the job.
On this model the finishing is not a separate line. Embossing and folding happen on the same web, in the same pass. That sentence is worth reading twice, because most CI presses stop after the last colour.
THREE OPERATIONS, ONE WEB PATH
The press prints four colours on a web up to 800 mm wide, with a maximum print width of 700 mm. It then embosses at a depth of 0.2 to 0.5 mm and folds to a depth of 0 to 100 mm. The fold line can sit at any angle between 0 and 45 degrees.
For an FFS heavy-duty bag, that replaces three operations and two extra handlings. The saving is not only time. Every extra handling is a chance to lose register, crease the web or trim the edge again.
The roll comes off the press printed, textured and folded, which is the difference between a printing shop and a bag line.
Converters adding this kind of work usually describe it as one installation rather than three. A press arriving on the floor changes the schedule of everything around it, not just the printing department.
WHY THE CENTRAL DRUM MAKES IT POSSIBLE
On a ci flexo printing machine, all four colour stations print against one large impression cylinder. The web stays on that drum while each station adds its colour, so register does not drift between stations the way it can on a stack press.
A stack press gives every station its own register control. A central drum does not need to, because the web never leaves the cylinder. Less to correct, and fewer metres lost while correcting.
The downstream stations inherit that stability. An embossing roller and a folding plough both work off the same tension and the same edge position, and if the web wandered the fold line would wander with it.
That is the argument for putting all three on one frame. Separately, each operation needs its own register and its own trim. Together, they share one. The direction the press builders are moving is the same one: fewer passes, more done inside one.
THE PRINT LENGTH WINDOW IS 360 TO 900 MM
Print length runs from 360 to 900 mm. Plate thickness is 1.7, 2.28 or 2.84 mm, with other sizes made to order, and the plate sits on 0.38 mm double-sided tape.
Plate thickness is a working choice, not a specification to copy. The 1.7 mm plate suits fine detail, the 2.84 mm plate carries deeper relief for a heavier ink laydown, and the job decides which one goes on the cylinder.
The window decides the bag sizes a shop can take. A short retail pouch and a 20 kg FFS sack do not share a repeat, and no amount of skill closes that gap. If the order book is mostly outside 360 to 900 mm, this is the wrong frame.
150 M/MIN IS A CEILING, NOT A SETTING
The sheet says 150 m/min, with a note attached: depending on the material, the ink and the complexity of the pattern. Read the note.
A four-colour solid with fine reverse type will not run at the same speed as a two-colour line job, and the ink system decides a lot of it. Water-based and solvent-based eco inks both run here, and each behaves differently on the same plate.
Plan capacity on the speed you actually hold, not the one on the plate. Award-winning flexo work is judged on the printed result, not on the meter reading.
WHAT THE MACHINE ASKS OF THE BUILDING
The unit weighs 25,000 kg and measures 15.2 by 3.5 by 4 m. It draws 100 kW, takes a roll up to 1,500 mm in diameter on a 6 inch air shaft, and holds tension between 5 and 20 kg across the full width.
Roll handling follows from the same figures. A 1,500 mm roll on a 6 inch shaft needs a lifting plan and clear floor in front of the unwind, not only a power drop.
Those are building numbers before they are machine numbers. Floor loading, crane access, door width and the power drop all get decided before the press arrives. Curing and drying belong in the same conversation, because they set the power and the floor space behind the last station.
WHERE IT STOPS MAKING SENSE
Three cases. Work that changes design every few hundred metres, where digital printing takes the job before flexo starts. Print widths above 700 mm. And shops that need neither embossing nor folding, who would be buying two stations they never use.
None of those are faults. They are the edges of the specification, and knowing them saves a year of arguing about output. Ask the question before the deposit, not after the first trial.
WHO SUPPLIES IT
This model, the CI flexo printing machine in the Master Series, is built by a partner manufacturer and supplied by XIAOPAI. Plate thickness, print length and fold depth are confirmed against the bag specification before the order is released.
The web usually arrives from a blown film line and leaves for a triplex laminator. The press sits between them, and the tolerance it holds is what the next two steps inherit. A register error found at the laminator is already three operations old.