Distribution Transformer Manufacturer China: The 8,760-Hour Column

2026-11-13 14:18 XIAOPAI
XIAOPAI · Wenzhou Xiaopai Electric Power Technology Co., Ltd. · Zhejiang, China

A distribution transformer manufacturer in China will send you a table with two loss columns, and most buyers read only one of them. The no-load figure looks small beside the load figure, so it gets treated as a rounding error. It is not, because it never switches off.

The arithmetic below decides more purchases than any efficiency class on the nameplate.

Printed in watts, the two figures look comparable. They are not. One is a standing charge and the other is a variable charge, and a table that prints them in the same font invites the wrong comparison.

TWO COLUMNS, TWO CLOCKS

Every distribution transformer manufacturer in China publishes the same two columns. No-load loss, sometimes called core loss, is paid from the moment the unit is energised. It runs 8,760 hours a year whether the plant is working or not.

Load loss, or copper loss, follows the square of the current. It only counts while the transformer is carrying load, and it grows fast when the load does.

Two clocks, one bill. A table that lists them side by side is inviting you to add them, not to compare them one at a time. The federal programme defines both, and the definitions are worth reading before the numbers.

620 W AT 1,000 KVA

Take two units of the same rating from one distribution transformer manufacturer's catalogue. The SCB10-1000/11 is a dry-type unit at 2,180 kg, with 1,770 W of no-load loss and 8,130 W of load loss.

The S11-1000/33 is an oil-immersed unit at 3,600 kg, with 1,150 W of no-load loss and 11,500 W of load loss.

The gap in the quiet column is 620 W. Multiply by 8,760 and it becomes 5,431 kWh a year. Ten years of service, and the difference is 54,312 kWh that one unit draws and the other does not, before a single ampere of load is connected. Twenty years in a basement turns it into 108,624 kWh.

THE CROSSOVER SITS AT 43 PERCENT

Now run the other column. The dry unit is 3,370 W better on load loss, so the advantage swings as the site gets busier.

620 divided by 3,370 is 0.184. Take the square root of that, because load loss follows current squared, and the crossover lands at about 43 percent of rated load.

The 43 percent belongs to this pair. A 630 kVA pair crosses somewhere else, and a 2,500 kVA pair crosses somewhere else again. The method travels; the number does not.

Below 43 percent average loading, the unit with the lower no-load figure uses less energy over the year. Above it, the unit with the lower load loss wins, and it keeps winning as the load climbs. Neither unit is better. One is better for a load profile.

WHAT YOUR SITE ACTUALLY LOADS

A site that runs lighting, telecom equipment or cold storage sits low for most of the day and peaks briefly. Its average load can be under 30 percent, and the quiet column dominates its bill.

A two-shift plant with a heavy day and an idle night sits somewhere near the middle, and the answer depends on the month.

A continuous industrial load runs high and flat, which is where load loss decides everything. Take a month of readings and compute the average, not the peak. The nameplate rating is not the load.

WHY THE STANDARD DOES NOT DECIDE FOR YOU

Efficiency standards test at a fixed per-unit load, 35 or 50 percent depending on the class, and set a floor. The final rule and the code behind it define that floor, and a compliant unit can still be the wrong unit for your curve.

Two compliant units of the same rating can differ by hundreds of watts in either column. The standard makes both legal. Only your load profile makes one cheaper to run.

That floor is also why both technologies survive. A dry-type unit can meet it with lower load loss and a higher no-load figure, an oil unit can meet it the other way round, and both pass.

THE MISTAKE OF COMPARING ONE COLUMN

Compare only no-load loss and every purchase turns into an oil-filled unit. Compare only load loss and every purchase turns into a dry-type. Both shortcuts are common, and both are wrong at the edges.

Weight belongs in the same conversation. The two units above differ by 1,420 kg, which is a floor loading, a crane and a door width before it is an electrical decision. Manufacturing capacity and lead time sit beside it, and so does what happens when one fails and a spare has to come from somewhere.

WHERE THESE NUMBERS COME FROM

The table behind this article runs from 25 kVA to 12,500 kVA and from 6.6 kV to 35 kV, with dry-type and oil-immersed units side by side. The 1,000 kVA pair above is a fair sample of how the two columns behave, not a special case. They are printed in watts so that they can be added, and the sum is the only figure that compares two units fairly.

XIAOPAI supplies these units from Wenzhou, Zhejiang, alongside dry-type transformers, oil-immersed transformers and switchgear. Send the load profile with the enquiry and the loss columns can be compared on your hours, not on a generic year. A site at 20 percent average load asks about the no-load column first, a site at 70 percent asks about the load column, and the question changes the answer.


Name:
Message:
Verification code:
Submit
Comment
contact us
Phone +86 13806536768
Whatsapp
Scan the QR code to inquire