A solventless laminating machine is not bought twice the same way. The first one replaces a process somebody else was running, so the decision is technical. The second one is bought because the order book grew, and the decision stops being technical and becomes structural. Two machines have to divide the work, share the people and sit in the same building without arguing over power and floor space.
The BD-1300A is the machine most converters look at for that second step. It runs at 400 m/min on a 1,250 mm web, takes 800 mm rolls on 3 inch or 6 inch cores, and carries 60 kW of installed power including 18 kW of heating. Those four numbers look like a specification list. In a second-line decision they are the four constraints everything else is built around.
THE FIRST NUMBER IS NOT CAPACITY
Capacity is the figure everyone calculates and the one that matters least. A machine at 400 m/min and a machine at 250 m/min do not differ by 150 m/min of output. They differ by how much of the week is spent running rather than setting up.
Start with the honest running hours. A plant running one shift on a 250 m/min machine can match a plant running one shift on a 400 m/min machine. The slower one only needs longer jobs and less time lost at change-over. Doubling the speed only helps the plant that already fills its hours.
So the first calculation is not how many metres the new machine adds per hour. It is how many hours of the week are currently consumed by change-over, cleaning and waiting for adhesive. Those hours are what a second machine buys back, and they are usually larger than the speed difference.
WHAT 400 M/MIN ACTUALLY BUYS
Four hundred metres per minute is a mechanical ceiling, and the material sets where it actually runs. The published range covers BOPP from 15 to 50 micron, PET and metallised PET from 12 to 30 micron, metallised CPP from 20 to 60 micron, LLDPE from 30 to 100 micron, glassine from 28 to 60 gsm and nylon from 15 to 100 micron.
Thin metallised film is where the ceiling holds. A 12 micron PET carries adhesive at a coating weight that barely changes with speed, so the drying and the nip pressure stay inside their window all the way up. A 100 micron PE film at the same speed needs the tension to hold a heavier mass, and the tension range is 3 to 30 kg across the full width on each unwind.
The alternative is extrusion coating rather than adhesive lamination, and the comparison is settled by the structure, not by the machine. The gap between mechanical speed and working speed is where a second line earns its place. One machine can be set for the thin structures that want 400 m/min, the other for the heavy structures that run at 250 and cannot be pushed. That split is worth more than a single machine running both at 300.
WIDTH DECIDES THE REST OF THE LINE
The 1,250 mm width is the number that connects the laminator to everything already in the building. A press wider than 1,250 mm produces rolls the laminator has to slit before it can run them. A slitter narrower than the laminator leaves trim that has to go somewhere.
The coating unit is a five-roller system. A metering roller of 150 mm runs without a drive and a transfer steel roller of 188 mm has its own servo. The transfer rubber roller sits at 150 mm and Shore A78, the coating steel roller runs at 188 mm on a separate inverter drive, and the coating rubber roller sits at 150 mm and Shore A80. Five rollers for one job sounds excessive until the adhesive is a two-component mix whose viscosity changes through the shift.
Surface energy is the other half of that bond, and treatment for flexible laminates decides how much adhesive the web will actually hold. Adhesive mixing is built in as the S-400 unit, and it talks to the host. When the mixer faults or runs short, the laminator alarms, slows down or stops. On a single line that is a convenience. On a second line it is the thing that keeps a night shift from running dry without anyone noticing.
ADHESIVE IS THE ONE VARIABLE THAT GROWS
Every other cost in a lamination plant is fixed by the building. Adhesive is the one that scales with output, and it is the one where a second machine changes the arithmetic.
Coating weight is set by the metering gap between the metering roller and the transfer steel roller, and the adjustment completes in one move rather than through a series of trial rolls. What the operator sets is not a number on a dial but a gap that produces a measured weight, and the repeatability of that gap is what makes the second machine predictable.
The chemistry is where the mistake usually sits. A solventless adhesive builds its final bond over hours, not seconds, and the review of process developments in multi-ply lamination is clear that the handling between coating and winding is what decides the result. A plant adding a second line often adds it to run the same structures faster, and then discovers that the cure time, not the machine, is the limit.
That is why the tension taper matters. Rewind tension runs from 4 to 40 kg across the full width with a taper from 0 to 100 percent. A roll wound at full tension holds its shape but blocks the cure at the core. A roll wound with too much taper goes soft and marks on the outside. The taper is the setting that lets a faster machine deliver a roll the next process can still use.
CHANGE-OVER IS THE COST NOBODY COUNTS
A second machine does not remove change-over. It moves it. Two machines running different structures means two set-ups instead of one, and the saving comes from being able to run both at the same time rather than sequentially.
The structures that matter here are the ones with a splice in the middle. Zero-speed splicing on the unwind is what keeps a line running through a roll change, and the tension disturbance it creates is the thing that shows up as a defect two hundred metres later. A machine without it stops at every roll.
The same logic applies to the roll itself. Automated splicing technology on coating and laminating lines exists because the roll change is the largest single interruption in a shift. A plant buying a second machine is buying the ability to make that interruption happen elsewhere.
The practical test is simple. Count the roll changes in a normal week. If the number is high enough that one machine spends more than an hour a day stopped for them, the second machine pays for itself in that hour alone, before any speed argument starts.
THE FLOOR, THE POWER AND THE WATER
The machine measures 5,600 by 2,800 by 2,450 mm and weighs about 8,500 kg. That footprint has to sit somewhere with clearance at both ends, because a roll of 800 mm diameter needs room to come off the shaft and a finished roll needs room to go onto a pallet.
Power is three phase five wire at 380 V and 50 Hz, with 60 kW installed and 18 kW of that in the heating circuit. The heating is split across two temperature control units. One covers the coating section, including the metering roller, the transfer steel roller and the coating steel roller. The other covers the laminating steel roller. That split is what lets the two sections hold different temperatures, and it is also why the electrical load arrives as two circuits rather than one.
Air is 0.7 MPa maximum and water is 2 to 4 kg per square centimetre. Both are easy to promise and easy to get wrong, because a second machine usually lands in a part of the building where the original services were sized for one line.
WHAT GOES INTO THE ORDER
Five things belong in the purchase order, and none of them is the number at the bottom. Name the material range with thickness, because a machine ordered for 12 micron PET and used on 100 micron PE will run at a different speed and a different tension. Name the coating weight window and the adhesive system, since a two-component mix needs the S-400 unit and a one-component system does not. Name the roll diameter and core size, because the 800 mm shaft and the 3 or 6 inch core decide what the slitter and the bag machine can take. Name the tension taper range, because it is the setting that connects this machine to the next one. Name the footprint and the service requirements, because the building decides those before the machine does.
XIAOPAI supplies the BD-1300A within its solventless range, alongside the WRJ i9 and the S1 digital machine, and the wider solventless laminating range covers the three-layer work where a single pass replaces two. The S3 triplex sits at the top of that range for plants moving from two passes to one.
A solventless laminating machine is the part of a second line that moves, and the decision around it is structural. The numbers that decide whether it pays are the hours it gives back, the width it shares with the press, the adhesive it consumes and the floor it needs. Get those four right and the speed takes care of itself.