A china obstructive film blowing machine is the phrase buyers use when they want a three-layer co-extrusion line rather than a single-layer one. The machine itself is straightforward to describe: three extruders feeding one die, a bubble, a rotating haul-off and a winder.
What is not straightforward is the film. Three layers give you three places to put a decision, and most of the arguments about quality happen because that decision was made by default rather than on purpose.
WHAT THE THREE LAYERS ARE FOR
The inner layer is the seal layer. It has to melt at a temperature the bag maker can reach, which is why it is usually a lower-melting resin than the rest of the structure.
The middle layer carries most of the mechanical job: stiffness, dart impact, tear resistance. It is also the layer with the most freedom, because it never touches the product or the printing press.
The outer layer takes the printing and the handling. It has to accept ink, resist scuffing, and look even. On a three-layer line those three jobs are separated, which is the whole point of the machine. barrier film lines keep pushing the same separation into more layers, but three is where most converters start.
THE LINE IN NUMBERS
The ABC 65/75/65 line runs three screws, all 30:1, in 38CrMoAlA with a PTA coating and a nitriding treatment. Output is 200 to 300 kg/hr. Maximum film width is 1,600 mm on a 1,800 mm frame.
Total installed power is 110 kW, on a 380 V, 50 Hz, three-phase supply. The machine stands about 12 by 6 by 10 m, with a three-layer platform and a second platform carrying the edge guide, the corona treater and the tension sensor.
Winding is a surface friction type, single or double sided, with hydraulic unloading on the double-sided version, a 16 N·m torque motor and an inflatable shaft. The winding range is 10 to 100 m/min.
WHAT ACTUALLY DECIDES FILM QUALITY
Not the screw diameter. Three things decide most of it: the layer ratio, the frost line height, and the haul-off ratio.
Layer ratio is set at the quotation, not at the machine. Move 10 percent of the thickness from the middle layer to the seal layer and the film seals at a lower temperature, but loses stiffness and tear strength. Nobody can see that change on the roll.
Frost line height is the operator's lever. Raise it and the film gets glossier but hazier and weaker in the transverse direction. Lower it and the film is tougher but rougher. Every material has a band where the two balance, and new film products keep widening the band, not removing the trade.
WHAT GOES WRONG IN THE FIRST WEEK
Three failures show up quickly. The bubble wanders because the air ring is not centred or the frost line is unstable. The seal fails because the layer ratio was copied from a different structure. The roll builds a ridge because the haul-off is not rotating.
The first two are commissioning problems and get fixed. The third follows the roll to the printer, where it is diagnosed as a printing problem, which is why it takes a month to trace. quality expectations have risen across the market, and a wrinkle that used to be tolerated now fails an inspection.
HOW TO SPECIFY ONE
Six items decide the offer on a china obstructive film blowing machine: film width, total thickness, layer ratio, resin family, winding type, and whether the haul-off rotates. Add the supply voltage and the working height if the building is already fixed.
Layer ratio is the one buyers leave out most often, and it is the one that changes the machine. A 20/60/20 structure and a 30/40/30 structure can use the same frame and produce different film, so the ratio belongs in the enquiry, not in a later email.
The same logic runs through the rest of the line. capacity additions and converters reworking are planned around a structure, not around a machine, which is why the structure is worth writing down first.
WHAT TO ASK THE SUPPLIER FOR
Four documents, and none of them is a brochure. First, the layer ratio drawing with target thicknesses. Second, the die gap and the number of spiral starts. Third, a film test report at the quoted output, not at half output. Fourth, the wiring and pneumatic drawings for the site team.
If the layer ratio is only discussed verbally, the machine will arrive set to whatever the factory last ran. That is the most common reason a new line produces film nobody approved.
WHO SUPPLIES IT
XIAOPAI supplies three-layer co-extrusion lines from Wenzhou, with and without a rotating haul-off, alongside the blown film machine, the laminating machine that follows it and the slitting line at the end of the line.
A china obstructive film blowing machine is not a different category of equipment. It is a three-layer line, and the three layers are where the value sits. Get the ratio and the frost line right, and the rest of the line behaves.