Slitter Rewinder Machine: One Frame, Four Finished Widths

2026-11-10 15:26 XIAOPAI
XIAOPAI · Wenzhou Xiaopai Electric Power Technology Co., Ltd. · Zhejiang, China

A slitter rewinder machine takes a wide master roll, cuts it into lanes and winds each lane into a finished roll. On this model the 1,300 mm in the name describes what the frame can hold, not what leaves the building. The finished widths are 450, 600, 650 and 900 mm, and all four come off the same machine.

That gap between the name and the output is the point of the design. One frame, one knife shaft and two rewind shafts cover four products, and the change between them is a setup rather than a second machine.

THE 1,300 IS A CAPACITY, NOT A PRODUCT

The unwind carries a master roll up to 1,500 mm in diameter on a 3 inch air shaft, braked by a 200 N·m magnetic powder unit. The web is 1,300 mm at its widest, and that figure sets the frame, the guide rollers and the shaft length.

Finished rolls run at 450, 600, 650 or 900 mm. Those are the four lanes the market asks for most often in non-woven, aluminium foil, plastic film and roll paper. A converter can supply all four from one floor position.

Buying one machine for four widths only works if the change is cheap. The parameters that decide it are the knife shaft, the guides and the rewind arrangement, not the motor size.

WHAT CHANGES WHEN THE LANE NARROWS

Ten circular knife sets sit on the shaft, and each lane needs its pair positioned to the millimetre. A 900 mm lane forgives a small error at the edge. A 450 mm lane has half the width to absorb the same error, so the trim is proportionally worth twice as much. The cutting method sets how clean that edge arrives.

On a slitter rewinder machine, this is where the guiding system earns its place. The correction range is 120 mm and the stated error is plus or minus 0.5 mm, read by a photoelectric sensor that follows the web edge. On a narrow lane, that tolerance is what keeps the wound face flat instead of stepped.

A stepped face is not a cosmetic problem. It travels downstream to printing and lamination as a tension variation, and it returns as register error or a wrinkle nobody can trace back to the slitter.

THE SECOND SHAFT IS THE SCHEDULE

Two rewind shafts sit at the rewind end. One takes a 400 mm roll, the other a second build, both on 3 inch air shafts and both driven through a 200 N·m magnetic powder clutch.

The second shaft is not redundancy. When a roll reaches its set length, the control system stops that shaft on the count and the web transfers to the other. The main line keeps running while the finished roll comes off, which is the difference between four widths being profitable and four widths being a scheduling problem. A converter buying a second machine is usually buying hours, not lanes.

The controller also trims speed to the line velocity, so a change does not arrive as a jolt in the web. A machine that stops for every roll change spends its day accelerating and braking, and the first metres of each roll show it.

SPEED AT FOUR WIDTHS

The mechanical maximum is 200 m/min and the working slitting speed is 150 m/min. The 50 m/min between them is the margin for acceleration, for a splice, and for the moment after a roll change when tension has to settle.

Narrow lanes do not run faster than wide ones on this frame. The limit is the material and the tension it will accept. A 450 mm lane of thin film reaches that limit sooner than a 900 mm lane of the same film, because the same brake torque is spread over less width.

The main motor is 5.5 kW, which sounds small for a machine handling a 600 kg master roll. It is enough because the motor is not cutting the web. It is overcoming friction and holding tension, and the knife separates the lanes with very little force.

WHAT THE FOUR WIDTHS ARE FOR

Non-woven goes to wipes and medical converters, aluminium foil to packaging and insulation, plastic film to flexible packaging, and roll paper to cores and wraps. Each material has its own trim habit and its own tolerance for edge quality.

The material decides the knife angle and the contact pressure more than the width does. A lane that runs clean in foil can burr in non-woven on the same setting, which is why the machine ships with a knife set rather than one knife type.

Master rolls arrive between 35 and 600 kg, and the frame is channel steel on a 1,200 kg build. The weight matters at the unwind, where a full roll has to be braked without bouncing the web.

WHAT TO CHECK BEFORE THE ORDER

Four things decide whether one frame really covers four widths. The narrowest lane and its trim allowance. The master roll diameter and weight the unwind will see. The tension the brake and clutch can hold at the smallest core. And the finished roll diameter the second shaft has to accept.

Ask for those four in writing against the machine, not against a family. A slitter rewinder machine that meets them on paper and not on the floor costs more than the second machine it was meant to replace. A plant that adds capacity usually finds the limit in one of those four before it finds it in the motor.

WHO BUILDS IT, WHO SUPPLIES IT

This model, the Type 1300 horizontal slitter rewinder, is built by a partner manufacturer and supplied by XIAOPAI. The knife set, the shaft sizes and the tension settings are confirmed against the material before the order is released.

The web usually arrives from a blown film line and leaves for a CI flexo press, and both ends of that chain set the tolerance the slitter has to hold.

Name:
Message:
Verification code:
Submit
Comment
contact us
Phone +86 13806536768
Whatsapp
Scan the QR code to inquire