Blown Film Machine Capacity: The Number Behind an Expansion Decision

2026-11-10 09:56 XIAOPAI
XIAOPAI · Wenzhou Xiaopai Electric Power Technology Co., Ltd. · Zhejiang, China

A blown film machine turns resin into a tube and winds the flattened tube into a roll. The number that decides whether a plant needs a second one is not on the specification sheet, because no sheet can know how many hours the line will actually run.

That number is saleable kilos per year, and it comes from three inputs multiplied together. Kilos per hour, hours at temperature and the share of output that passes inspection cover the whole calculation, because everything else about a blown film machine sits inside one of those three.

ONE LINE, ONE YEAR

Catalogues print output per hour because it is the easiest figure to put on a page. A plant lives on output per year, which is a different and much smaller number.

The conversion is simple: take the hourly rate, multiply by the hours the line spends running, then multiply by the yield. The result is the film you can invoice, and it is usually forty to sixty per cent below the number a buyer remembers from the brochure.

This is why two plants with identical machines report different capacity, and why neither of them is lying.

THE FIRST INPUT: KILOS PER HOUR

This line is rated from 200 to 300 kg per hour, and the band exists because thickness changes what an extruder can do. The same three screws push more kilos of thick film than of thin film in the same hour.

Three screws run at 65, 75 and 65 mm with an L/D of 30:1, driven by 30, 37 and 30 kW motors. The middle screw is the larger one because the core layer carries most of the volume, and the outer layers are thin skins.

Where a plant lands in that band is decided before the machine arrives. A line running 1,600 mm at the thin end of the 0.001 to 0.01 mm range will sit near the bottom. A line running heavy film at the same width will sit near the top.

Capacity steps in the film trade tend to arrive in one move rather than in tenths. A 40 per cent jump is one version of that move, and a new blown film line beside existing presses is another.

THE SECOND INPUT: HOURS AT TEMPERATURE

Hours are the input plants overestimate most often. A three shift operation sounds like 8,760 hours a year, and no blown film line has ever run that number.

Six thousand hours is a realistic figure for a plant running three shifts, five days a week, with maintenance and holidays removed. It already assumes the line starts on Monday morning and stops on Friday night without drama.

Two things eat those hours without appearing as breakdowns. A changeover stops the line while the new job settles, and a roll change stops it again at whatever frequency the order book demands. Neither is a fault, and both belong in the hours figure rather than in a footnote.

Production efficiency is usually discussed as a property of the machine, yet on a blown film line it is closer to a property of the calendar.

THE THIRD INPUT: THE SHARE THAT PASSES

Yield is the input that gets argued about. On this line the thickness tolerance is plus or minus 4 per cent on LDPE, and film outside that window is scrap even when the bubble looks fine.

Start-up film belongs here too. Every job begins with film that is the right colour and the wrong gauge, and that film is produced at full speed and never sold.

A plant that counts yield honestly, including start-up and edge trim, usually finds a number between 85 and 92 per cent. A plant that counts only visible rejects will claim 97 per cent and wonder why the warehouse disagrees.

THE THREE TOGETHER

Put the inputs together and the differences become visible. One line runs 250 kg per hour for 6,000 hours at 90 per cent yield, which gives 1,350 tonnes of saleable film in a year.

A second line runs 200 kg per hour for 5,000 hours at 85 per cent yield, which gives 850 tonnes. The two machines may carry the same model plate, and the gap between them is 500 tonnes a year.

That gap is not a machine problem. It is one line running more hours, at a better point in the thickness band, with less film lost at the start of each job.

WHAT IT MEANS FOR EXPANSION

Once the three inputs are on one page, the expansion question answers itself. If hours are already near 6,000 and yield is above 90 per cent, the line has nothing left to give and a second machine is the only way to add capacity. A converter who doubled capacity with a new line did it because the old one had no hours left, not because the old one was slow.

If hours are at 4,500, the cheaper capacity is already inside the plant. It sits in the changeovers, the roll changes and the start-up film, and a second machine would arrive with the same losses attached.

The physical side is worth checking before either decision. This line needs twelve metres by six metres by ten metres of floor and 110 kW on a 380 V, 50 Hz, three phase supply, and both are easier to confirm than to install later.

Regions that are adding film capacity run the same three inputs at a larger scale. What a buyer should leave with is one page: kilos per hour at the thickness they actually run, hours they can realistically staff, and yield they are willing to measure honestly. The blown film machine fills in the first line of that page and nothing else.

WHO BUILDS IT, WHO SUPPLIES IT

This line, the ABC65/75/65-1800 with the rotary haul-off, is manufactured by SINSTAR and supplied worldwide by XIAOPAI as authorised distributor. The specification, the pre-installation document and the commissioning coordination stay with one team from the first enquiry to handover.

Film from this line usually leaves for printing on a CI flexo printing machine, or for narrower widths on a slitting machine. Both steps inherit whatever the three inputs produced, which is the reason to write them down before the order.

Name:
Message:
Verification code:
Submit
Comment
contact us
Phone +86 13806536768
Whatsapp
Scan the QR code to inquire